Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Bendix EC-80 Cartridge Lifetime Prediction Reset Test by JPRO

Posted on September 1, 2023 by
Bendix EC-80 Cartridge Lifetime Prediction Reset Test by JPRO (2)

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Here is the instruction show you guide on how to perform Cartridge lifetime prediction reset for Bendix EC-80 by JPRO Diagnostic Software.This test provides the ability to reset the Cartridge Lifetime Remaining value to 100% after a new air dryer cartridge has been installed.

 

Related Contents:

JPRO Noregon Commercial Fleet Diagnostics 2023 2021 Free Download

Noregon JPRO DLA+ 2.0 Adapter

 

Procedures:

1 Select Cartridge Lifetime Prediction Reset Test and press Enter or the Start Button.

2 The test dialog will be displayed.

Bendix EC-80 Cartridge Lifetime Prediction Reset Test by JPRO (1)

NOTE: Reset should only be performed after a new air dryer cartridge has been installed.
3 Click the Reset button to reset the Cartridge Lifetime Remaining value to 100%. The Wetness Level and Total Air Delivered values will also be reset.
4 Selecting Additional Info will display important test and repair information, including explanations for related faults. Click Exit to close this screen.

Bendix EC-80 Cartridge Lifetime Prediction Reset Test by JPRO (2)

 

Cartridge Lifetime Prediction Reset Information:

The CLP Reset should only be performed after a new air dryer cartridge has been installed. Resetting the CLP without changing the cartridge can lead to moisture and water in air system.

Cartridge Lifetime Remaining (SPN 13073) indicates between 100% for a fresh cartridge to 0% for

an expired cartridge. After CLP Reset is performed, Cartridge Lifetime Remaining will read 100%.

 

For specific instructions, see AD-HFi Service Data Sheet SD-08-12046.

The following faults are the ones related to Cartridge Lifetime Prediction and the actions to take:

Cartridge maintenance prediction pre-worn alert (Flash Code 30-1), SPN 521610, FMI 15:

This indicates the cartridge is approaching its lifetimne limit (15% lifetimne remaining or less).

Cartridge may be replaced and CLP Reset run.

 

Cartridge maintenance prediction nominal alert (Flash Code 30- 2), SPN 52610, FMI 16:

This indicates the cartridge has reached its lifetime limit or 0% lifetime remaining. Cartridge must be replaced and CLP Reset run.

 

Cartridge maintenance prediction over-worn alert (Flash Code 30-3), SPN 521610, FMI 0:

This indicates that the cartridge has been in service beyond its service lifetime. This fault also

indicates there may be water in the air system. Check reservoirs for water via drain check valves and service accordingly. Cartridge must be replaced and CLP Reset run.

 

5 When done, press the Exit button to return to the test selection dialog.

More topics about JPRO Diagnostic,please refer to:JPRO Diagnostics Guide

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Bendix EC-80 Cartridge Lifetime Prediction Reset Test by JPRO From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: Jungheinrich ETM/V 10-12 Forklift Truck Parking Brake Test
Next: Next: How to Solve New Holland CX8000 Touchscreen Display Doesn

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Scania Truck ALM 000800 Interrupted LIN Communicatin Siren
  • BMW G Series BDC2 Module Virgin and Replacement by APPRO2
  • CG FC200 V1.2.9.2 Update: BMW Coolant Temperature Setting Added
  • Scania Truck ALM 000463 Motion and Inclination Detector,Calibration Fault
  • How to Solve JCB Excavator P0615-13 Starter Relay Open Circuit Error

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2