Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low

Posted on December 7, 2024 by VCDS

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Allison 3000 & 4000 Gen5 P0642 trouble code:Sensor Reference Voltage “A” circuit low indicate that something wrong in TCM.Here chinaobd2.com will show you guide on how to solve Allison 3000 & 4000 Gen P0642 problem.

Allison 3000 & 4000 Gen 5

For more Diesel machine repair,please refer to:

2023 Diesel DTC Solutions V2.9.98+ Diesel Explorer 2.0+Instruction

2024 2019 Allison DOC Transmission Diagnostic Software Free Download

DIAGNOSTIC RESPONSE:

Default sensor data used

CIRCUIT DESCRIPTION:

This test detects when the 5V reference circuit voltage provided by the TCM and used by certain transmission control components such as the OLS, TFT, analog TPS,and RMR device is detected below specification for a period of time.

ACTION TAKEN WHEN THE DTC SETS:

When DTC P0642 is active, the following conditions occur:

1 The CHECK TRANS light is illuminated.

2 DTC is stored in TCM history.

3 Additional DTCs active depending on 5V reference to function normally.

CONDITIONS FOR CLEARING THE DTC/CHECK TRANS LIGHT:

Use the NEXIQ USB Link 2 diagnostic tool to clear the DTC from the TCM history. The TCM automatically clears the DTC from the TCM history if the vehicle completes forty warm-up cycles without failure.

DTC P0642 may be caused by:

1 Irregular TCM or vehicle power.

2 Poor TCM or vehicle grounds.

3 If multiple DTCs are noted in failure records, this DTC may indicateOEM Transmission unapproved components spliced into W158 or W103, or W103 shorted to chassis ground.

4 W112 or W158 short to ground, high resistance or open.

5 Broken or defective connector assemblies allowing pushed back pins to short together.

6 Unlocked connectors, missing seal plugs allowing moisture in connectors.

DIAGNOSTIC AIDS:

Review applicable information in CONTROL SYSTEM AND TRANSMISSION SPECIFICATIONS to find additional circuit specifications, system and connector diagrams, and troubleshooting tips.

More Allison repair case,please refer to Allison Trouble Repair

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Related Posts
How to Activate Windows 7 without Product Key |Windows is Not Genuine
Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low

Some Friends don't know how to activate win7, when they receive the diagnostic software with win7 sytem. http://www.chinaobd2.com/upload/software/win7activation.zip download this Read more

How to Install Original Mercedes BENZ EPC/WIS/ASRA net |China OBD2 Store
Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low

Please ensure that you choose computer systems that meet our requirements for the installation. You will find adetailed listing in Read more

How to Replace Benz W204 Engine Oil Filter
Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low

Frequent oil changes are perhaps the most important procedure you can do to maintain and prolong the life of your Read more

Toyota Previa MPV Smart Card All Keys Lost Programming Guide
Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low

Toyota Previa is an MPV produced by Toyota since 1990. It is called Estima (?????) in the Japanese market and Read more

This Post: Allison 3000 & 4000 Gen5 P0642 Sensor Reference Voltage “A” Circuit Low From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: HITACHI 4JJ1 Engine P0087 Fuel Rail Pressure Limiter Open Solution
Next: Next: Massey Ferguson Tractor 6700 SPN 94, FMI 3 Fuel Pressure Sensor Voltage Above Normal

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • How to Remove and Replace Cab Heater Controls for JCB 3CX Loader
  • How to Remove Differential Gear for FENDT 900 Vario COMIII
  • Quick Tips to Use Xhorse BMW G Series BDC2 Adapter
  • International MaxxForce 7 SPN 27 FMI 4 EGRP Signal Out of Range Low
  • Detroit DD13 SPN 84 FMI 3 MCM Vehicle Speed Sensor Open Circuit

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine ComputerTabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • VCDS on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • Glynn McKay on Scania SDP3 2.59.1 free download Scania Diagnosis & Programming 3 download link
  • jakub brosz on Scania SDP3 V2.64.3 Download link
  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • Launch CRP129 HD
  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer

Links

  • BOBD2 Auto Diagnostic Tools Market
  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2