Skip to content
Menu
OBD2 Scanner Blog
  • Home
  • Car Diagnostic Tool
    • MB Star Diagnosis
    • BMW Diagnostic Tool
    • GM Tech2
    • Volvo Vocom Interface
  • OBD2 Code Scanner
    • VXDIAG
  • Tech Support
OBD2 Scanner Blog

Allison 3000 & 4000 Gen 5 C1312 Fault Code Solution

Posted on January 3, 2024 by VCDS
Allison 3000 & 4000 Gen 5

Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation

Here is the illustration show you guide on how to repair and solve Allison 3000 & 4000 Gen5 fault code C1312 retarder request sensor circuit low.

Allison 3000 & 4000 Gen 5

DIAGNOSTIC RESPONSE:

Inhibits retarder operation if not using J1939 datalink

 

For more Diesel machine repair,please refer to:

2023 Diesel DTC Solutions V2.9.98+ Diesel Explorer 2.0+Instruction

 

CIRCUIT DESCRIPTION:

The TCM may be calibrated to receive a Retarder Modulation Request (RMR) signal from a retarder request sensor, sometimes called a resistance module or RMR device. If used, the input is monitored by software, which then controls a retarder pressure solenoid.

 

NOTE: J1939 Retarder Select, Non-Engine (RSNE) and/or TSC1 messages may be used in addition to or instead of an RMR sensor to request the amount of retardation desired.

 

The TCM is connected to the retarder request sensor by:

1 A 5V reference voltage (W112),

2 Retarder request signal (W156), and

3 Analog ground (W158).

 

The sensor produces a retarder request signal in response to inputs from the retarder control device(s). The TCM interprets this signal as a percent retarder request.

 

ACTION TAKEN WHEN THE DTC SETS:

When DTC C1312 is active, the following conditions occur:

1 The TCM does not iluminate the CHECK TRANS light.

2 DTC is stored in TCM history.

3 The retarder will no longer apply based on input from the RMR sensor.

 

CONDITIONS FOR CLEARING THE DTC/CHECK TRANS LIGHT:

Use the diagnostic tool to clear the DTC from the TCM history. The TCM automatically clears the DTC from the TCM history if the vehicle completes 40 warm-up cycles without failure.

 

DIAGNOSTIC AIDS:

DTC C1312 indicates the TCM has detected a voltage signal from the retarder request sensor in the low error zone and may be caused by the following:

1 Open or short to ground in W112 or W156 circuits.

NOTE: Shorts or opens in W112 typically will log other sensor filed low DTCs that are using W112 (5V), such as the Oil Level Sensor (OLS), Electronic Brake System (EBS) pressure sensor, or analog Throttle Position Sensor

(TPS). Shorts or opens in W156 (RMR analog signal) only causes DTC C1312.

2 Analog retarder request input (i.e. RMR inputs) enabled during TCM programming without RMR module.

3 Non-retarder application has autodetected retarder or had the CMC Override Retarder Autodetect set to

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

This Post: Allison 3000 & 4000 Gen 5 C1312 Fault Code Solution From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

Post navigation

Prev: Prev: How to install v17.04.27 wiTECH Micropod 2
Next: Next: Linde Truck Doctor 2.01.05 Forklift Truck Diagnostic Free Download

Leave a Reply Cancel reply

Your email address will not be published. Required fields are marked *

Recent Posts

  • Yanhua Module 38 Update BMW BDC2 Reflash and Replace Functions
  • Vapon Update BDC2 IMMO Module Data Erase
  • How to Replace U17 and L8 Components for OBDSTAR G3 Startup Failure?
  • Alientech Kess3 Adds Master TCU OBD-Bench-Boot Protocol
  • Scania Truck ALM Alarm System ALM404 Fault in the CAN Communication Solution

Recommend OBD2 Scanner

ME9.7 ECU Engine Computer ME9.7 ECU Engine Computer TabScan T6PT3G Diagnosis VCI for Porsche Diagnostic Tool Porsche Diagnostic Tool

Recent Comments

  • amr on MAN EOL Flash File Editor + MAN Immo Calculator Free Download
  • Pasquale Greenwald on Jungheinrich ETM/V 10-12 Tightening Torque for Screwed Connection on Brake Systems
  • VCDS on Scania SDP3 2.53.1 Diagnosis & Programming Free Download
  • Crossley on What are the functions of Iprog+ Programmer?
  • Lukas on VAG EDC15 EDC16 IMMO OFF Software Free Download

Archives

Categories

  • BMW Diagnostic Tool
  • Car Diagnostic Tool
  • Key Cutting Machine
  • Key Programming Tool
  • MB Star Diagnosis
  • OBD2 Code Scanner
  • Tech Support
  • VXDIAG

Tags

adapter Auto Pick and Decoder Car Key Copy Car Key Programmer cat Code Reader diagnostic software ECU Chip Tunning ecu programmer Ford gm handy baby Handy Baby 2 Key Programmer Handy Baby II Key Programmer HEX V2 immo iprog key Key Pro key programmer laptop Launch lish LISHI new arrivals nexiq nexiq link diesel truck interface nexiq truck diagnostic NEXIQ USB Link OBD2 obdii original program Scania VCI smart VAG COM Cable VCDS VCDS Cable VCDS VAG COM Cable vci VW wholesale X-PROG Box X-PROG Box ECU Programmer XPROG-M

Hot Selling

  • ME 9.7 ECU Engine Computer
  • MINI VCI J2534
  • NCF29XX Programmer
  • ThinkTool Pros+

Links

  • China OBD2
  • EPS Foam Machine
  • Foxdiag
  • Сканер OBD2
©2025 OBD2 Scanner Blog | Powered by chinaobd2