OBDSTAR P50 Battery Reset Update V30.06: Add Audi BMS 8R0915233,8R0915591 crash record erase and repair (by bench). In Audi A6, AB and Q5 hybrids, the hyorid battery management unit (BMS) disconnects and logs a P1609 fault code when a crash occurs. (!! Crash shut-down activated !!), resuling in the vehicle not starting. At present,only a…

How to update Super ICOM Pro N3+ firmware? It supports updates online. ICOM-BootImage and ICOM-ApplicationImage bin files need to be updated. The upgrade steps are the same as the original ICOM or ICOM clone. Before upgrade, check the current firmware version and download the newest version. 1.Open ITool Radar tool on desktop and check the current ICOM firmware version, such as it is…

Super ICOM Pro N3+ J2534 /DOIP One Key Switch Function Use Guide: Super ICOM Pro N3+=BWM special inspection+J2534+DOIP+WIFI Super ICOM Pro N3+ supports both DOIP and J2534, and has a one-key switch button to freely switch between ICOM software and J2534/DoIP software. Super ICOM Pro N3+ can use the J2534 protocol to read through after switching…

Super ICOM Pro N3+ can use the J2534 protocol to read through after switching with one key. It is compatible with the 6-pin and 14-pin CAN communication and the 7-pin K-line communication of the OBD port. It can use Volkswagen, Mercedes-Benz, Toyota, Honda, Land Rover and other special inspection software with J2534 interface. Here is…

CG FC200 ECU programmer with the new MPC5xx Adapter  read and write BMW BOSCH EDC16CP35 MPC563/4 in bench mode. Steps: First, connect CG FC200 to one computer via the USB cable, and also connect with a power supply Then, run FC200 V1.1.3.0. Select BMW>> 5-Series (E60)>> 2993 M57D30O2 235>> BOSCH EDC16CP35 MPC563/4>> Platform Next, check the wiring…

Xhorse VVDI Key Tool Plus BMW motorcycle key learning guide: Detail Steps: Connect Key Tool Plus to BMW Motorcycle Enter “Immo programming” function Tap BMW>> Select from system>> BMW motorcycle key learning>> Coding function Tap “Key function” to see the instruction, and tap “Start programming” Step 1: Read vehicle information It reads out the data fast….

Launch X431 V+ shows: Your device is corrupt, it can’t be trusted and will not boot. How to solve? Solution: Reflash the tablet Reflash files Download: 1.QUD.WIN.1.1 Installer-10040.5.zip 2.QPST.WIN.2.7 Installer-00447.3.zip 3.emmc_appsboot_printlog_and_repair.mbn Two Steps to reflash the X431 V+ tablet: 1. Use Qfil to flash into the special aboot.img 2. Use Qfil to reflash back to…

Launch X431 IMMO Plus/X431 IMMO Elite with IMMO function can do anti-theft key matching on Lincoln (Ford). It has been tested on Ford Aviator 2022, works like a charm! Procedures: Connect Launch X431 IMMO key programmer and vehicle Enter IMMO function Select Ford>> Ford Anti-theft software>> Anti-Theft Key Matching>> Automatically Search Set ignition switch to ON Confirm the…

Xhorse Condor XC-MINI Plus II Common Error and Solution Customer problem: When I use Xhorse Condor XC-Mini Plus II, the probe is not going into the axis more than that (see the figure below), and received an exception report “error code 5: probe detected…”. Solution: Your mistake is that the milling cutter and the probe are not on the same level. Please unscrew the screw,…

All American Buick GL8 from 2017- till now use the new BCM (body computer module) which has the vehicle’s mileage data. Previously, it needed a filter for dashboard mileage adjustment. But now, it can be done with CG100X easily without a filter. CGDI CG100X Buick GL8 2017-2023 D70F3558 (BCM) wiring diagram Main points: Need to connect 6 cables…

Launch X-431 Anti-theft Key Matching Tool (X431 IMMO Plus/X431 IMMO Elite) with Chrysler Anti-theft diagnostic software can perform functions such as key matching, anti-theft module replacement, and password reading for Chrysler/Jeep/Dodge series, and ECUs cover wireless control module, radio frequency hub, body control module and more systems. Here takes 2016 Chrysler Ram 1500 Radio Frequency Hub- Tire…