Diagzone Xdiag Subscription Renew, LAUNCH LTR-01 RF Sensor, Thinkdiag Renew , Scania SDP3 Installation
New Arrival I-2014 Multi-Diag Access J2534 Pass-Thru OBD2 Device
Top 4 Reasons to Get I-2014 J2534:
1. Latest Version: V2014.01
2. Support Multi-languages: English, Spanish, German, French, Italian, Portuguese, Bulgarian, Croatian, Czech, Danish, Dutch, Finnish, Hebrew, Hungarian, Polish, Romanian, Russian, Serbian, Slovenian, Swedish, Turkish
3. Support 23 Brands Updated, 5300 New Systems
4. Operating System: Windows XP; Windows 7 32bit
3. Support 23 Brands Updated, 5300 New Systems
4. Operating System: Windows XP; Windows 7 32bit
Notice:
1. Do not connect with internet, and before you install the software, follow our video to install software and driver correctly
1. Do not connect with internet, and before you install the software, follow our video to install software and driver correctly
2. I-2014V Multi-Diag Access J2534 needs activation, after installing the software pls send ID (format is 31-xxxxxxxxxxx) to us, we will send the activation code.
Installation Multi-diag 1-2014:
1). Open folder (1) Key on the CD and run the file KeyUpdate. Then confirm and wait for the message "successfully installed XXXXXX" and click "OK"
2). Start the installation folder (2) 1-2014 During your installation, if the software request an unlock key 31-xxxxxxxxxx, please contact us with the key to obtain an activation code.
3). Select the language, then it will continue to install, please wait until the software complete installation, usually it will take about 30 minutes to 2 hours, how much time to wait it depends on your computer configuration. When the message display saying "Multi-Diag is currently installed with profile ACTIA. Before you can use the program, you must restart your computer." Click "No, I will restart my computer later" and click "Finish"
4). Go to the following folder C: ACTIA portal and then delete the file "WEGT.EXE", and clean "Recycle Bin"
5). After delete this file, open folder (1) Key on the CD and run the file KeyUpdate. Then confirm and wait for the message saying "successfully installed XXXXXX" and click "OK"
6). Then install "xs-ime-pt-207p-workshop.exe". At the step, please connect the device to the car, then use the USB cable to connect with the computer, then it will prompt to install Pass Thru driver.
7). Go to My Computer – Properties – Hardware – Device Manager, when you find PC- 201411261510 – I+ME ACTIA XS Device and PassThru+ XS USB Driver, it means Multi Diag Access has successfully establish communication with the computer.
Then you can restart the pc.
Multi-Diag J2534 Functions:
After selecting the car manufacturer, then you can make the diagnosis for the different menus on offer (depending on cars models):
1. Maintenance
Diagnosis codes from all computers
Reset maintenance interval
Modification of the sewage
Read / erase fault calculators
Maintenance of the particulate filter
2. Air Conditioning
Diagnosis of cooling electronic
Reading settings cooling circuit,
Test servo actuators
3. Pollution control
Diagnosis of the particulate filter
Electronic control of pollutant emissions
Control of the Lambda probe
4. Liaison to the ground
Electronic configuration of the size of tires,
Electronic configuration of tires (winter / summer),
Setting valves tire pressure
Diagnosis and management of shock-driven
Calibration of the sensor angle Driving (initialization of the steering angle)
5. Body
Implementation of safety airbags (lock / unlock)
Reconfiguration of a new calculator Airbag,
Diagnosis of calculators Airbag,
Rain sensor windshield (reading and erasing fault)
Test panel and activators of lights,
Setting Xenon headlights,
Rear radar
6. Post-Equipment
Setting up the radio,
Configuration loader CD,
Setting alarms
Configuration of the coupler,
Configuration bicycle loading system
7. Braking
Diagnosis of calculators ABS, ESP.
Diagnosis and unlock electric brakes.
Flush the brake system.
8. Motor
Diagnosis of any calculator injection engine (diesel, gasoline, flexfuel, etc. ..)
Programming of injectors
Electronic configuration of the EGR valve
9. Expert Mode
Diagnosis of advanced computers,
Configuration of comfort functions,
Change the language of the instrument panel,
physical measures (option with a probe – not supplied)
Direct access to all functions of diagnosis.
V2014.1 Multi Diag Access J2534 System Requirements:
*CPU: Pentium/Athlon 1.8 GHz or higher
*RAM: 256 MB of system memory
*Hard Drive: 10 GB of available space
*VCI (vehicle communication Interface)
*DVD-ROM
*No Internet, WIFI
*No Antivirus software
Multi-Diag J2534 Software Display:
How to connect the J2534 and cables:
Multi-Diag J2534 Packing List:
VCI (Vehicle Communication Interface)
DB25 to OBD-2 Male cable
OBD2 Male to OBD2 Female cable
DB25 to OBD-2 Male cable
OBD2 Male to OBD2 Female cable
Promotion I-2014 Multi-Diag Access J2534 Pass-Thru OBD2 Device
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: j2534 J2534 interface j2534 programmer multi dig access J2534 Multi-Di@g Access Multi-Diag Multi-Diag J2534 interface
Related Posts
How to Configure DTS Monaco 9.02 with VXDIAG VCX SE
2024.01.28
How to choose PCMTuner
2023.04.13
Toyota Techstream 14.00.018 Download FREE
2019.03.5
Exploring Autel J2534 with JLR Pathfinder and Topix Cloud
2024.12.9
V2013.1 Upgrade Chip for Multi-Di@g J2534 Interface
2018.12.17
What is j2534 pass thru?
2019.06.3
Promotion V2019.3 MB SD C4 Connect Compact 4 Star Diagnosis with WIFI for Cars a...
2019.02.17
Only US$155.00 NEXIQ USB Link Truck Scanner tool for Vietnam Valid untill 2019/2...
2019.02.18
How to Use Ford IDS with FVDI J2534 Diagnose for Ford Focus 1.6L
2019.06.17
Autel MaxiFlash Pro J2534 ECU Programming Tool Works with Maxisys 908/908P
2018.12.17