This article show a guide on how to use Launch X431 tool to program remote keyless entry for Jeep Cherokee.
If you are interest in Launch X431,here is a articles collection:How to use LaunchX431
What Models work?
1999 – 2002 (AB) Ram Van/Wagon
1999 – 2002 (AN) Dakota
1999 – 2002 (BR/BE)Ram Pickup
1999 – 2002 (DN) Durango
2002 (DR) Ram Pickup
2001 – 2002 (JR) Sebring Sedan/Stratus Sedan/Sebring Convertible
2002 (KJ) Liberty
1999 – 2002 (LH) Concorde/Inytrepid/LHS/300M
1999 – 2000 (NS) Town & Country/Caravan/Voyager
1999 – 2002 (PL) Neon
1999 – 2002 (PR) Prowler
2001 – 2002 (PT) PT Cruiser
2001 – 2002 (RS) Town & Country/Caravan/Voyager
1999 – 2002 (WJ) Grand Cherokee
1999 – 2001 (XJ) Cherokee
And for more key programming on Jeep,please check here:Jeep Key Programming
DISCUSSION:
A Remote Keyless Entry (RKE) Programming Procedures Card (Publication No.81-170-00011) is being provided with this Technical Service Bulletin to simplify RKE transmitter programming on 1999 – 2002 North American vehicles.Additional copies of the RKE publication, 81–170–00011 (Fig. 1), can be ordered from DDS Distribution Services, LTD. Their number is 1-800-890-4038.
NOTE: THE RECENTLY RELEASED MILLER SPECIAL TOOL, “RF DETECTOR NO. 9001”, SHOULD BE USED TO DETERMINE IF THE TRANSMITTER IS WORKING BEFORE BEGINNING PROGRAMMING PROCEDURES. THERF DETECTOR INDICATES IF THE TRANSMITTER IS WORKING, NOT IF IT IS PROGRAMMED TO A VEHICLE.
Daimler Chrysler North American Remote Keyless Entry Programming Procedures
Daimler Chrysler North American Remote Keyless Entry Programming Procedures
NOTE: PLEASE READ INSTRUCTIONS FULLY BEFORE ATTEMPTING TO PROGRAM TRANSMITTERS.
Program Method A (Customer Program Method)
1.Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attemptto function transmitter, if working as designed discontinue programming.
2.Turn ignition to run position. (Allow ignition chimes to stop).
3.Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.
4.Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).
5.Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).
6.Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).
NOTE: (FOR DR 0NLY ) A CHIME WILL NOT SOUND ON STEP #6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.
7.Repeat steps 5 through 6 to program additional transmitters.
8.Turn ignition to OFF position. Transmitter programming mode will discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).
Program Method B (Customer Program Method)
1.Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2.Turn ignition to the run position (Allow ignition chimes to stop).
3.Using original transmitter, press and hold the [UNLOCK] button on the transmitter for between 4 and 10 seconds.
4.Continue to hold the [UNLOCK] button and press the [PANIC] button. A chime will sound to indicate that the transmitter programming mode has been entered (Allow 3 seconds for chime to sound).
5.Press a button on all transmitters to be programmed into the system including any previously programmed transmitters; a chime will sound when each transmitter has been programmed.
6.Turn the ignition to OFF position to exit the transmitter programming mode.
Program Method C (Dealer Program Method) *Can be used for any type transmitter.
1 .Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.
2.Turn ignition to the run position (Allow ignition chimes to stop).
3.Plug DRBIII to vehicle’s 16–way data link connector.
4 .Follow Service Manual and DRBIII instructions to program transmitters.
Program Method D (For use with AB vehicles not equipped with VTSS only)
1.Locate the dark green program enable wire connected to pin #1 of the 16-way data link connector under the left side of the instrument panel.
2.Connect the program enable wire terminal to a good ground.
3.Insert the key into the ignition and turn the ignition switch to the ON position. The power locks will cycle (Lock and Unlock) indicating that program mode has been entered.
4.Using the transmitter to be programmed, press either [LOCK] or [UNLOCK]. The power locks will cycle indicating the transmitter has been programmed successfully.
5.Repeat step 4 to program additional transmitter.
6.Disconnect the program enable wire from ground to exit program mode.
7.Turn the ignition to the OFF position and remove the key.
NOTE: REFER TO DAIMLERCHRYSLER MDS2 SYSTEM OR PARTS DEPARTMENT TO OBTAIN THE CORRECT PART NUMBER AND REVISION FOR SPECIFIED VEHICLE.
How useful was this post?
Click on a star to rate it!
Average rating / 5. Vote count:
Please keep this link if you copy the post!
Tags: cat key Key Pro Key Programming Launch Launch X431 original program Remote remote key X431
Related Posts
Caterpillar ET 2018A Electronic Technician Software Free Download
2019.07.24
Autocom Delphi 2021.11 Ds150e Software Cars Trucks Free Download and Installatio...
2024.01.28
JCB 3CX/4CX/5CX Foot Throttle Position Sensor Remove/Install and Test Guide
2024.03.12
How to Remove and Disassemble Instrument Cluster for BMW Z3
2019.05.31
Launch X431 IV X431 GX4 Master Auto Scanner Update Version
2018.12.17
Iveco AlphaNumeric Code Calculator v0.1 Free Download
2019.05.14
Best Quality VCM II Diagnostic Tool With WIFI Function for Ford V98
2018.12.17
2019 Latest Version TOYOTA Techstream 14.20.019 Free Download and Activation
2019.08.7
How to Disable DPF for BOSCH EDC17C81 EDC17C53 EDC17C63
2023.04.2
How to use gm tech2
2024.01.28